• We’re currently investigating an issue related to the forum theme and styling that is impacting page layout and visual formatting. The problem has been identified, and we are actively working on a resolution. There is no impact to user data or functionality, this is strictly a front-end display issue. We’ll post an update once the fix has been deployed. Thanks for your patience while we get this sorted.

Glue that is not glue?

Buckman

Buckman

I want to stick to items together so that they will stay stuck to one another for a long time, but when it comes to separate the items it is not a hard job i.e. a Veneer / Formica does not lift and a good rub removes glue residue. Thanks.
 
TonyH1 said:
Hi Buckman, it will depend on what the two things being stuck together are made of.
Click to expand...
And further:
What shape are the objects, how much surface area will be stuck, will it need to resist water, and or heat (how hot) Will it need to resist sunlight and what type of forces will it need to resist.
 
It is to stick down a washbasin to a surface with Formica on top. The washbasin is more or less flat undernath and the glue would be there to stop it turning, but may have to be removed if at some point it requires a repair, modification etc. We have a washbasin that has very steep sides and is narrow making it difficult for me to wash my face etc. The new basin is wider and the sides lower and it is easier for me to access. If at some point in the future we need to sell the caravan, the original basin will need to be fitted and then Formica surface is exposed so any traces fo glue will need to be removed.
 
Absolutely, bathroom silicone, clear or White to suit. Great stuff re moves with a knife or scraper and patience and you can buy silicone remover too if needs be but you can usually scrape it off Formica.
 
Go gently and thin on the silicon. Be sure you can cut around the joint and use silicone remover to clean up all surfaces.
 
I would be using Copydex a natural latex, not a silicone.
The latex will serve well to stop water ingress, can be readily cut off with dental floss "cheese-wire" with zero damage risk and peels readily with just finger rubbing. It is aslo less prone to mildew.
 
Last edited:
JTQ said:
I would be using Copydex a natural latex, not a silicone.
The latex will serve well to stop water ingress, can be readily cut off with dental floss "cheese-wire" with zero damage risk and peels readily with just finger rubbing. It is aslo less prone to mild dew.
Click to expand...

You really don't want to get a mild dew on anything. 🤣

Often these plastic sinks have a rounded edge profile ending in a small contact area. Literally bedding it in silicone gives a complete seal, overspill is easily cleaned off impervious surfaces.


John
 
  • Like
Reactions: JTQ
If all you require from the "glue" is to stop that turning is there not an alternative concept to glueing?
What about a tailored wood batten slipped behind it and against the side/back board, basically just an anti turn "key"?
A discrete short bit fixed on some mirror tape.

Or even plonk the basin down on a couple of strips of mirror tape; I fixed a mirror to the wall of our van back in 2008 with that brand of tape and it's still there 35,000 miles plus later.
 
JTQ said:
If all you require from the "glue" is to stop that turning is there not an alternative concept to glueing?
What about a tailored wood batten slipped behind it and against the side/back board, basically just an anti turn "key"?
A discrete short bit fixed on some mirror tape.

Or even plonk the basin down on a couple of strips of mirror tape; I fixed a mirror to the wall of our van back in 2008 with that brand of tape and it's still there 35,000 miles plus later.
Click to expand...

Thanks for the hint. Hopefully the basin will arrive today so I can really suss it out.
 
On reflection, I would design for venting under the bowl rather than attempting to "seal" it down, particularly with a silicone on a work top surface in an application that by thats very nature will be bouncing about during towing. With a used worktop there could well be traces of polish, soaps etc that could act as release agents to any bond, if leaving the surface untreated so suitable for retrospective use.
 
You must log in or register to reply here.

TRENDING THREADS

Latest posts

Back
Top